page 1 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com case style: mt1818 the big deal product overview JSW2-33DR-75+ is a high-power refective spdt rf switch, with refective short on output ports in the off state. made using a silicon-on-insulator process, it provides very high ip3 (55 dbm typ.). this switch also has a built-in cmos driver and negative voltage generator, all packaged in a tiny 2x2mm package, enabling it to operate over wideband and ft into tight spaces. feature advantages wideband operation 5-3000 mhz enables a single component to be used in a vast array of applications from vhf up to 3 ghz. high iip3: 55 dbm typ. results in little or negligible inter-modulation generation, meeting requirements for digital communication signals. low loss, 0.38 db at 1 ghz & high input power, 3w low loss and high power capability enables a single switch to be used for a variety of applications, saving inventory. built in negative voltage generator operates with single positive supply voltage; no need for dc blocking capacitors, unless external dc is present at the rf ports. built-in cmos driver no need for external driver, saving pcb space and cost. tiny mclp package 2 x 2mm, 12-lead provides low inductance, repeatable transitions, and excellent thermal contact to pcb. key features 75 ? 5 to 3000 mhz high power 3w ? single positive supply voltage ? high power p0.1db greater than 3w ? low insertion loss, 0.33 db at 1 ghz JSW2-33DR-75+ spdt rf switch
page 2 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com product features ? high isolation, 42 db typ. at 1 ghz ? low insertion loss, 0.38 db typ. at 1 ghz ? high ip3, 56 dbm typ. at 1 ghz ? low current consumption, 37 a typ. ? high power, p0.1db 3w general description JSW2-33DR-75+ is a high power (35 dbm) refective spdt switch with integral cmos driver, operates with single positive supply voltage while consuming, 37 a typical. jsw is a refective short on output port in off state. it has been designed for very wideband operation of 5-3000 mhz. it is packaged in a tiny 2mm x 2mm x 0.55mm package and is rated msl1 and class 1b for esd (hbm) JSW2-33DR-75+ rev. c m153173 JSW2-33DR-75+ rs/th/cp 151002 rs/th/cp 75 ? 5-3000 mhz simplifed schematic and pad description refective rf switch with internal driver. single supply voltage, +2.3v to +4.8v, high power 3w function pad number description rf com 2 rf common/ sum port, (see fig. 2) rf1 11 rf out #1/in port #1, (see fig. 2) rf2 5 rf out #1/in port #2, (see fig. 2) control 7 cmos control in vdd 9 supply voltage enable 8 shutdown mode enabled by connecting to logic low gnd 1,3,4,6,10,12 ground case style: mt1818 typical applications ? catv systems ? satcom system ? automated test stations spdt rf switch +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications
page 3 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com rf electrical specifcations (1) , 5 - 3000 mhz, t amb =25c, v dd = +2.3 to 4.8v parameter condition (mhz) min. typ. max. units frequency range 5 3000 mhz insertion loss (2) (on state) 5 to 1000 0.38 0.48 db 1000 to 1500 0.48 0.58 1500 to 2000 0.54 0.64 2000 to 3000 0.53 0.64 isolation between common port and rf1/rf2 ports 5 to 1000 40 42 db 1000 to 1500 35 38 1500 to 2000 32 35 2000 to 3000 28 31 isolation between rf1 and rf2 ports (3) 5 to 1000 40 45 db 1000 to 1500 35 41 1500 to 2000 32 37 2000 to 3000 28 32 return loss (on state), all ports 5 to 1000 19 db 1000 to 1500 16 1500 to 2000 16 2000 to 3000 17 input ip3 ( v dd =3v ) 5 to 1000 56 dbm 1000 to 1500 62 1500 to 2000 63 2000 to 3000 63 0.1db input compression (4) 5 to 3000 35.0 dbm dc operating electrical specifcations parameter min. typ. max. units vdd, supply voltage 2.3 4.8 v supply current 37 a control enable voltage low 0 0.4 v control enable voltage high 1.65 vdd v control current 1 a shutdown mode - supply current 7 a switching specifcations parameter min. typ. max. units rise/fall time (10 to 90% or 90 to 10% rf) 0.5 (rise time) 0.7 (fall time) sec switching time, 50% ctrl to 90/10% rf 1.9 (on time) 1.1 (off time) sec video feed-through, (control 0 to 1.65v, freq.=10 khz) 3.0 mv p-p notes: 1. tested on mini-circuits test board tb-723-n+ (see characterization test circuit, fig.1). 2. insertion loss values include test board loss. 3. enable voltage hi, either rf1 or rf2 are on. 4. do not exceed rf input power as shown in absolute maximum rating table. spdt rf switch JSW2-33DR-75+
page 4 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com absolute maximum ratings (5) parameter ratings operating temperature -40c to +85c storage temperature -40c to 125c v dd , supply voltage 5.0v voltage control -0.2v min. v dd max. rf input power 5 watt 6 truth table (state of control and enable voltage selects the desired switch state) state of: rf common to control voltage enable voltage rf1 rf2 high high on off low high off on low/high low shutdown on- low insertion loss state off- isolation state 5. operation of this device above any of these conditions may cause permanent damage. 6. derate linearly to 2.5w at 85c. characterization test circuit test equipment: for insertion loss, isolation, return loss: agilents n5230a network analyzer , e3631a power supply. mini-circuits matching pad unmp-5075-33+ for switching time and video feed through agilents ag54832b hp81110a pulse generator, hpe3631a network analyzer , e3631a power supply. agilents n90a spectrum analyzer , e8257d generator u200a for compression: r&s network analyzer zva24, e3631a power supply. conditions: v dd = +2.3 and +4.8v, control= 0 and 1.65v. for insertion loss, isolation and return loss: pin=0 dbm for input ip3 : pin=+10dbm/tone. for switching time: rf frequency: dc at 0 dbm, control frequency: 500 khz and 0 and +1.65v. figure 1: block diagram of test circuit used for characterization. (dut soldered on mini-circuits tb-723-n+) spdt rf switch JSW2-33DR-75+
page 5 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com recommended application circuit product marking j2 1 12 black body fig. 2: evaluation board includes case, connectors and components soldered to pcb. spdt rf switch JSW2-33DR-75+
page 6 of 6 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com msl test flow chart esd rating human body model (hbm): class 1b (500 to < 1000v) in accordance with jesd22-a114 machine model (mm): class a (pass 100v) in accordance with jesd22-a115 msl rating moisture sensitivity: msl1 in accordance with ipc/jedec j-std-020d additional notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp visual inspection electrical test sam analysis refow 3 cycles, 260c soak 85c/85rh 168 hours bake at 125c, 24 hours visual inspection electrical test sam analysis start finish additional detailed technical information additional information is available on our dash board. to access this information click here performance data data table swept graphs case style mt1818 plastic package; lead fnish: nipd au tape & reel f108 standard quantities available on reel 7 reels with 20, 50, 100, 200, 500, 1k or 3k devices suggested layout for pcb design pl-415 evaluation board tb-723-f+ environmental ratings env75 spdt rf switch JSW2-33DR-75+
|
